2014 Honda CR-V Oil Capacity
The 2014 Honda CR-V uses different oil capacities depending on the engine option. The base 2.4-liter four-cylinder engine holds approximately 4.2 quarts (4.0 liters) of oil with a filter change, while the optional 3.5-liter V6 engine requires roughly 4.6 quarts (4.4 liters). These figures include the oil filter and are based on a complete drain and refill. Always confirm the exact specification for your particular trim and drivetrain before purchasing oil.
More from this site
Keep reading the latest coverage
Using the wrong amount of oil can lead to inadequate lubrication, increased engine wear, or in severe cases, engine damage. Overfilling can cause foaming, reduced lubrication, and increased pressure on seals. Underfilling can result in insufficient oil pickup and overheating. Sticking to the manufacturer's specified capacity and viscosity protects the engine and maintains warranty coverage.
Engine Specifications and Oil Type
The 2014 CR-V was offered with two distinct engines, each with its own oil requirements. The 2.4-liter inline-four is the more common option and uses 0W-20 viscosity oil, which Honda recommends for its balance of fuel efficiency and cold-start protection. The 3.5-liter V6, found in the higher trims, also uses 0W-20 oil in most markets, though some regions may specify a different viscosity based on local climate conditions.
| Engine | Oil Capacity (with filter) | Recommended Viscosity | Filter Type |
|---|---|---|---|
| 2.4L i-VTEC I4 | 4.2 qt / 4.0 L | 0W-20 | Honda proprietary cartridge |
| 3.5L V6 | 4.6 qt / 4.4 L | 0W-20 | Honda proprietary cartridge |
Checking and Maintaining Oil Level
To check the oil level on a 2014 CR-V, park the vehicle on a level surface and wait a few minutes after shutting off the engine to allow the oil to settle. Pull the dipstick, wipe it clean, reinsert it fully, then pull it again to read the level. The oil should fall between the minimum and maximum marks on the dipstick. If the level is low, add oil in small increments and recheck to avoid overfilling.
Honda recommends checking the oil level at least once a month and before long trips. The 2014 CR-V is equipped with an oil life monitoring system that tracks driving conditions and alerts the driver when an oil change is due, but manual checks remain important for catching leaks or consumption issues early.
Oil Change Procedure and Filter
Changing the oil on a 2014 CR-V involves draining the old oil, replacing the oil filter, and refilling with the correct amount of new oil. The oil filter is a cartridge-style unit located near the front of the engine. After installing a new filter, it is important to refill with the precise capacity specified for your engine to ensure proper lubrication and avoid triggering the low-oil warning.
Use only Honda-certified oil filters and oil that meets Honda's specifications, typically marked as meeting API SN or SP standards with the correct viscosity. After completing the oil change, run the engine for a few minutes, check for leaks, and recheck the oil level with the engine off and the vehicle on level ground.
Common Oil Capacity Questions
- How much oil does a 2014 Honda CR-V take? The 2.4L engine takes 4.2 quarts; the 3.5L V6 takes 4.6 quarts, including the filter.
- Can I use 5W-30 instead of 0W-20? Honda specifies 0W-20 for the 2014 CR-V. Using a different viscosity may affect engine performance and warranty coverage.
- How often should I change the oil? Follow the Honda maintenance schedule and oil life monitor, typically every 5,000 to 7,500 miles depending on driving conditions.
Always refer to the owner's manual for your specific 2014 CR-V trim and engine configuration. The manual provides the definitive oil capacity, viscosity, and maintenance interval for your vehicle, which may vary slightly from the general figures listed here.